「ccet」の検索結果

Description。This SparkFun Triple-Axis Accelerometer Breakout is a simple Qwiic breakout for the KX132 digital accelerometer from Kionix. The KX132 is a low-power， 16-bit resolution three-axis accelerometer with four user-selectable acceleration measur

Description。The LIS3DH Breakout is a smart， low-power， three-axis， capacitive micro-machined accelerometer with 12 bits of resolution that you can use to add translation detection to your project. It would be classified as a 3DoF， or 3 Degrees of Free

Description。The SparkFun ADXL313 Breakout is a low power， high resolution(up to 13-bits)3-axis accelerometer for measurement up to ±4g. This breakout measures the static acceleration of gravity in tilt-sensing applications， as well as dynamic accel

Description。Though the Clincher connector can be used with FFCs， we also like to use them with our FlexiForce sensors and other flex/force sensors found in the。Recommended Products。section below.。Note：。Please be aware that we will not be able to accept returns on this connector if it has been closed. Sorry for any inconvenience this may cause.

Description。Though the Clincher connector can be used with FFCs， we also like to use them with our FlexiForce sensors and other flex/force sensors found in the。Recommended Products。section below.。Note：。Please be aware that we will not be able to accept returns on this connector if it has been closed. Sorry for any inconvenience this may cause.

Description。Note：。Since these cables belong to our "Ding &； Dent" category， once we are out of stock， we will not carry it again. Get them while you can! We also cannot accept requests/returns/exchanges， provide documentation， or provide supp

Description。Note：。Since these cables belong to our "Ding &； Dent" category， once we are out of stock， we will not carry it again. Get them while you can! We also cannot accept requests/returns/exchanges， provide documentation， or provide support on any aspect of these items.。Features。28 AWG

Description。These Clincher connectors from Amphenol FCI can be used to terminate Flat Flexible Cables(FFCs)to an easy-to-use standard header. Simply insert the end of the cable into the connector and press it closed. The teeth inside the connector will "clinch" around the conductors and break them out to three male 0.1" spaced pin headers!。Though the Clincher connector can be used with FFCs， we also like to use them with our FlexiForce sensors and other flex/force sensors found in the。Recommended Products。section below.。Note：。Please be aware that we will not be able to accept returns on this connector if it has been closed. Sorry for any inconvenience this may cause.

。Description。The SparkFun 9DoF IMU Breakout incorporates all the amazing features of Invensense's ICM-20948 into a Qwiic-enabled breakout board complete with a logic shifter and broken out GPIO pins for all your motion sensing needs. The ICM-20948 itself is an extremely low powered， I2C and SPI enabled 9-axis motion tracking device that is ideally suited for smartphones， tablets， wearable sensors， and IoT applications. Utilizing our handy Qwiic system， no soldering is required to connect it to the rest of your system. However， we still have broken out 0.1"-spaced pins in case you prefer to use a breadboard.。In addition to the 3-Axis Gyroscope with four selectable ranges， 3-Axis Accelerometer， again with four selectable ranges， and 3-axis magnetometer with an FSR to ±4900μT， the ICM-20948 also includes a Digital Motion Processor that offloads the computation of motion sensing algorithms from the detectors， allowing optimal performance of the sensors. We've also broken out all the ICM-20948 pin functionality to GPIO and labeled them I2C on the front， SPI on the back for ease of identification.。Note：The I2C address of the ICM-20948 is 0x69 and is jumper selectable to 0x68. A multiplexer/Mux is required to communicate to multiple ICM-20948 sensors on a single bus. If you need to use more than one ICM-20948 sensor consider using the Qwiic Mux Breakout.。The SparkFun Qwiic Connect System is an ecosystem of I2C sensors， actuators， shields and cables that make prototyping faster and less prone to error. All Qwiic-enabled boards use a common 1mm pitch， 4-pin JST connector. This reduces the amount of required PCB space， and polarized connections mean you can't hook it up wrong.。Need a custom board? This component can be found in SparkFun's A La Carte board builder. You can have a custom design fabricated with this component - and your choice of hundreds of other sensors， actuators and wireless devices - delivered to you in just a few weeks.。Get Started with the SparkFun ICM-20948 9DoF IMU Guide。Features。1.95 V to 3.6 V supply voltage。Triple-axis MEMS gyroscope with user-programmable full-scale range of ±250 dps， ±500 dps， ±1000 dps， and ±2000 dps。Triple-axis MEMS accelerometer with programmable full scale range of ±2g， ±4g， ±8g， and ±16g。Triple-axis silicon monolithic Hall-effect magnetic sensor with full scale measurement range to ±4900 μT。I2C at up to 100 kHz(standard-mode)or up to 400 kHz(fast-mode)or SPI at up to 7 MHz for communicationwith registers。On-board digital motion processor(DMP)。Digital-output temperature sensor。2x Qwiic Connection Ports。I2C Address：0x69(0x68 with Jumper)。。Documents。Schematic。Eagle Files。Hookup Guide。Datasheet(ICM-20948)。Arduino Library。Python Support(Qwiic_Py)。GitHub Hardware Repo

Description。This is the official case for the Raspberry Pi 3 Model A+(it also fits the Raspberry Pi 1 Model A+ as well). The case is a two-piece ABS press-fit enclosure with access to the USB， HDMI， Audio， and Ethernet ports. A slot on the bottom gi

Description。Do you own micro：bit or micro：bit Go Bundle and want to expand your skills with the new microcontroller? You are in luck! The SparkFun Inventor's Kit Bridge Pack for micro：bit was designed to provide you with an easy way to transform your m：b into full fledged learning kit! Each Bridge Pack includes all of the parts found in the SIK for micro：bit that aren't included with the Go Bundle. With the SIK Bridge Pack for micro：bit you will be able to complete circuits that will teach you how to read sensors， move motors， build Bluetooth(R)devices and more.。The micro：bit is pocket-sized computer that lets you get creative with digital technology. Between the micro：bit and our shield-like bit boards you can do almost anything while coding， customizing and controlling your micro：bit from almost anywhere! You can use your micro：bit for all sorts of unique creations， from robots to musical instruments and more. At half the size of credit card， this versatile board has vast potential!。Note：The Bridge Pack is NOT full SparkFun Inventor's Kit and only includes the parts to complement micro：bit Go Bundle or standalone board. That also means that this kit does。not。include micro：bit， which will need to be purchased separately.。Get started with the micro：bit SIK Experiment Guide。Examples。Circuit 0：Hello， micro：bit!。Circuit 1：Blinking an LED。Circuit 2：Reading Potentiometer。Circuit 3：Reading Photoresistor。Circuit 4：Driving an RGB LED。Circuit 5：Reading an SPDT Switch。Circuit 6：Reading Button Press。Circuit 7：Reading the Temperature Sensor。Circuit 8：Using Servo Motor。Circuit 9：Using Buzzer。Circuit 10：Using the Accelerometer。Circuit 11：Using the Compass

Description。The SparkFun Inventor's Kit(SIK)for micro：bit v2 is a great way to get creative， connected and coding with the micro：bit. The SIK for micro：bit v2 provides not only the micro：bit v2 board but everything you need to hook up and experiment with multiple electronic circuits! With the SIK for micro：bit v2 you will be able to complete circuits that will teach you how to read sensors， move motors， build Bluetooth(R)devices and more.。The SparkFun Inventor's Kit for micro：bit is the latest and greatest in single-board computer kits. Surrounding the micro：bit v2 SIK is one core philosophy --- that anyone can(and should)experiment with cutting-edge electronics in a fun and playful way without breaking the bank.。The kit does not require any soldering and is recommended for all users， from beginners to engineers. We have provided a complete Experiment Guide in the Documents tab for you to check out now! If you have ever been interested in learning about electronics， or if you have used the original SparkFun Inventor's Kit and are looking for something new， the SIK for micro：bit is the perfect kit for you!。The micro：bit is a pocket-sized computer that lets you get creative with digital technology. Between the micro：bit and our shield-like bit boards you can do almost anything while coding， customizing and controlling your micro：bit from almost anywhere! You can use your micro：bit for all sorts of unique creations， from robots to musical instruments and more. At half the size of a credit card， this versatile board has vast potential!。。Examples。Circuit 0：Hello， micro：bit!。Circuit 1：Blinking an LED。Circuit 2：Reading a Potentiometer。Circuit 3：Reading a Photoresistor。Circuit 4：Driving an RGB LED。Circuit 5：Reading an SPDT Switch。Circuit 6：Reading a Button Press。Circuit 7：Reading the Temperature Sensor。Circuit 8：Using a Servo Motor。Circuit 9：Using a Buzzer。Circuit 10：Using the Accelerometer。Circuit 11：Using the Compass

Description。Sweepy 2.0 is our new Dust Boot made from clear polycarbonate.。Version 2.0 features a number of enhancements， that stem from customer feedback. These include：Sweepy 65 V2 - now can now travel up and down the spindle body allowing greater flexibility when milling。Now fits a 2.5" Shopvac as standard。Includes adapters for：2.5" direct hose。2.25" shop vac。36mm Festool/Fein。Includes our affectionally-named "Winston" a clear brush free base for 3d carving and video making。This 69mm size is for the Dewalt spindles.。Sweepy mounts directly to your spindle and is clamped with a machined quick-release. The compact design means that no travel is lost， and it works with any Shapeoko Z-axis with no adapters. The lower half is detachable and held in place using neodymium magnets， which means that the top half remains in place while the lower half detaches for easy access when changing bits.。(For the legal sticklers out there， the Shapeoko and Compact Router shown in the photos are not included with Sweepy.)

Description。The micro：bit v2 Educator's Lab Pack includes 10 micro：bit v2 boards and everything you need to get you started with the new learning platform. The Lab Pack has everything you need， including micro：bits， cables， battery packs and a few parts to experiment with. This package provides an easy way to introduce your students to the micro：bit without any difficulty or parts hunting.。SparkFun packages everything educators need to get started with the micro：bit in a variety of classroom settings and learning environments. The hardware boards， cables and extra parts come pre-packaged. Examples and curriculum materials are available from SparkFun and micro：bit， as well as from other educators involved in this growing maker education movement.。Lab Packs are your classroom entry point. By combining our kits， popular boards and other educational tools with support materials(to be updated)， SparkFun brings all the power of the open source community to the classroom. We've also updated the battery pack to be closer to what is in other micro：bit kits. It now requires 2xAAA batteries.。The micro：bit is a pocket-sized computer that lets you get creative with digital technology. Between the micro：bit and our shield-like bit boards you can do almost anything while coding， customizing and controlling your micro：bit from almost anywhere! You can use your micro：bit for all sorts of unique creations， from robots to musical instruments and more. At half the size of a credit card， this versatile board has vast potential!。。Features。Micro：bit 2.0：64 MHz Arm Cortex-M4 with FPU。512KB Flash。128KB RAM。5x5 Red LED Array。Two Programmable Buttons， one touch sensitive logo。MEMS microphone and LED indicator。Onboard Light， Compass， Accelerometer， Temp Sensors and Speaker。2.4 Ghz Micro：bit Radio/BLE 5.0 Smart Antenna。25-pin Edge Connector。4 dedicated GPIO， PWM， i2c， SPI， and ext. power。Three Digital/Analog Input/Output Rings。Two Power Rings --- 3V and GND。Dedcated I2C bus for peripherals。MicroUSB Connector(5V)。JST-PH Battery Connector(。Not。JST-XH)(3V)。Power/reset Button with Status LED。200 mA available for accessories。Program with C++， MakeCode， Python， Scratch

。Description。The official case for the Raspberry Pi 4. This case ships as two parts made of ABS plastic with access to all USB， HDMI， Audio/Video， USB and Ethernet ports. In addition， a slot on the bottom gives access to the MicroSD card. The top and bottom parts are press fit and comes in two-tone black and gray.

Description。The Xcelite 8-in-1 Screwdriver Set provides eight high-quality bits in a single ergonomic tool. Each bit is easily accessible with a spring-loaded magnetic housing that holds the seven included bits you aren't currently using. Though the screwdriver set includes eight unique bits， the end of the shaft features a 0.25" hex driver that can fit most of your existing 1/4" bits. With a strong magnetic hold and no-roll handle design， this is one of the best all-in-one tools we have used!。The shaft of this multiple-tip driver is made from a chrome-molybdenum vanadium steel that makes for great durability and longevity.

Description。The SparkFun weather：bit is a fully loaded "carrier" board for the micro：bit that， when combined with the micro：bit， provides you with a fully functional weather station. With the weather：bit you will have access to barometric pressure， relative humidity and temperature readings. There are also connections on this carrier board to optional sensors such as wind speed， direction， rain gauge and soil readings! In this version we have also added a vertical Qwiic connector. The micro：bit has a lot of features and a lot of potential for weather data collection.。The weather：bit connects to the micro：bit via an edge connector at the top of the board， making setup easy. This creates a handy way to swap out micro：bits for programming， while still providing reliable connections to all of the different pins on the micro：bit. We have also included serial and I2C headers on the weather：bit for optimized connectivity if you so choose.。The micro：bit is a pocket-sized computer that lets you get creative with digital technology. Between the micro：bit and our shield-like bit boards you can do almost anything while coding， customizing and controlling your micro：bit from almost anywhere! You can use your micro：bit for all sorts of unique creations， from robots to musical instruments and more. At half the size of a credit card， this versatile board has vast potential!。Note：The SparkFun weather：bit does。NOT。include a micro：bit board. The micro：bit will need to be purchased separately.。Get started with the weather：bit Guide。Features。Onboard temperature， humidity， and pressure sensor。Connectors(PTH and screw terminal)for soil moisture and soil temperature。Connectors(RJ11)for wind speed， direction and rainfall gauges。Edge connector for easy micro：bit integration。Vertical Qwiic connector。Headers for Serial and I2C communication

Description。You'll have no need for a screwdriver with this terminal! This is a 3-pin Latch Terminal with 5mm pitch pins. Each pin is rated up to 250V @ 11A and will line up well with the standard 0.19" spacing. Please note that the pins are thick enough(1.20mm OD)that you may need to increase the hole diameter on some boards. Each of the terminals can accept 18-22AWG wire.。Features。Latch Terminal。5mm Pitch。3-Pin。Tin Plated Brass Terminals。18-22AWG Wire Range。Operation Temperature：-55℃～+100℃

Description。You'll have no need for a screwdriver with this terminal! This is a 4-pin Latch Terminal with 5mm pitch pins. Each pin is rated up to 250V @ 11A and will line up well with the standard 0.19" spacing. Please note that the pins are thick enough(1.20mm OD)that you may need to increase the hole diameter on some boards. Each of the terminals can accept 18-22AWG wire.。Features。Latch Terminal。5mm Pitch。4-Pin。Tin Plated Brass Terminals。18-22AWG Wire Range。Operation Temperature：-55℃～+100℃

Description。The SparkFun RTK Surveyor is an easy to use GNSS receiver for centimeter-level positioning. Perfect for surveying， this preprogrammed device can also be used for autonomous driving， navigation， asset tracking and any other application where there is a clear view of the sky. The RTK Surveyor can also be used as a base station. With the flick of a switch， two RTK Surveyors can be used to create an RTK system capable of 14mm horizontal positional accuracy. The built-in Bluetooth(R)connection via an ESP32 WROOM enables the user to use the RTK Surveyor with their choice of GIS application on a phone or tablet. The built in battery allows field use for up to four hours and is compatible with common USB battery banks.。This device can be used in four modes：GNSS Positioning(～30cm accuracy)。GNSS Positioning with RTK(1.4cm accuracy)。GNSS Base Station。GNSS Base Station NTRIP Server。In Position mode the device receives L1/L2 signals from a user-provided antenna and the high-grade GNSS receiver provides lat/long and altitude with accuracies around 300mm.。In Positioning with RTK mode the device receives L1/L2 signals from the antenna and correction data from a base station. The correction data can be obtained from a cellular link to online correction sources or over a radio link to a 2nd RTK Surveyor setup as a base station.。In Base Station mode the device is mounted to a temporary position(like a tripod)and begins transmitting correction data over a radio or internet connection. A base is often used in conjunction with a second unit set to 'Positioning with RTK' to obtain the 14mm relative accuracy.。In Base Station NTRIP Server mode the device is mounted to a semi or permanently fixed position(like a roof)and connects over WiFi to transmit the correction data to a NTRIP caster so that any rover can access the correction data over a cellular or internet connection. This type of base is a very easy way to setup a very precise absolute correction source.。Two cables are provided with the RTK Surveyor allowing a user to plug on our easy to use Serial Telemetry Radios or their own radio link. If a local correction source is within 10km， a user can also use their phone to provide correction data over the Bluetooth(R)link(no external radio needed!).。Note：The SparkFun RTK Surveyor is just the enclosed device and does NOT include an antenna， serial telemetry radio， or associated mounting pieces. These items will need to be purchased separately from the Hookup Accessories below.。Get Started With the SparkFun RTK Surveyor Guide。Features。GNSS Receiver：ZED-F9P。Concurrent reception of GPS， GLONASS， Galileo and BeiDou。Receives both L1C/A and L2C bands。Current：68mA - 130mA(varies with constellations and tracking state)。Time to First Fix：25s(cold)， 2s(hot)。Max Navigation Rate：PVT(basic location over UBX binary protocol)- 25Hz。RTK - 20Hz。Raw - 25Hz。Horizontal Position Accuracy：2.5m without RTK。0.010m with RTK。Max Altitude：50km(31 miles)。Max Velocity：500m/s(1118mph)。Bluetooth(R)Transceiver：ESP32 WROOM。Xtensa(R)dual-core 32-bit LX6 microprocessor。Up to 240MHz clock frequency。16MB of flash storage。520kB internal SRAM。Integrated 802.11 BGN WiFi transceiver。Integrated dual-mode Bluetooth(R)(classic and BLE)。Hardware accelerated encryption(AES， SHA2， ECC， RSA-4096)。2.5 μA deep sleep current。Overall Device。Internal Battery：LiPo 1000mAh with 500mA charging。Radio Port：3.3V TTL Serial(57600bps RTCM TX/RX)。Data Port：3.3V TTL Serial(115200bps NMEA)。Weight：132g(entire device including battery)。Dimensions：118mm×79mm×30mm(4.7in×3.1in×1.2in)。1x Qwiic Connector。1x microSD Socket for optional logging。Changes：This version(which replaces SPX-17369)uses a reinforced edge mount SMA connector for better resiliency when a fixed 'stub' antenna is used.

。Description。Product Restrictions：To access certain features of the ATECC608A， users will need to contact Microchip and sign an NDA contract to obtain the complete datasheet. Due to the required NDA - technical support， an Arduino library， and hookup guide are not provided for users on this product.。The SparkFun ATECC608A Cryptographic Co-processor Breakout allows you to add strong security to your IoT node， edge device， or embedded system. This includes。a。symmetric。authentication，。symmetric。AES-128 encryption/decryption， and much more. As stated above， the ATECC608A has limited Arduino support and the complete datasheet is under NDA with Microchip.。This breakout board includes two Qwiic ports for plug and play functionality. Utilizing our handy Qwiic system， no soldering is required to connect it to the rest of your system. However， we still have broken out 0.1"-spaced pins in case you prefer to use a breadboard. The ATECC608A chip is capable of many cryptographic processes， including， but not limited to：Creating and securely storing unique asymmetric key pairs based on Elliptic Curve Cryptography(FIPS186-3).。AES-128：Encrypt/Decrypt， Galois Field Multiply for GCM。Creating and verifying 64-byte digital signatures(from 32-bytes of message data).。Creating a shared secret key on a public channel via Elliptic Curve Diffie-Hellman Algorithm.。SHA-256 HMAC Hash including off-chip context save/restore。Internal high quality FIPS random number generator.。Embedded in the chip is a 10Kb EEPROM array that can be used for storing keys， certificates， data， consumption logging， and security configurations. Access to the sections of memory can then be restricted and the configuration locked to prevent changes. Each ATECC608A Breakout ships with a guaranteed unique 72-bit serial number and includes several security features to prevent physical attacks on the device itself， or logical attacks on the data transmitted between the device.。A summary datasheet for the ATECC608A is available here. The full datasheet is under NDA with Microchip. You will need to contact them for access to the entire datasheet. Meanwhile， the ArduinoATECCX08 Library currently only supports the ATECC608A with SAMD21 Arduino boards.。We do have much more support for the ATECC508A version of this chip. Please check out our ATECC508A Hookup Guide and Arduino Library(which includes six examples). This will get you familiar with the basics of elliptic curve cryptography and signing/verifying data with the ATECC508A version of the chip.。Note：The I2C address of the ATECC608A is 0x60 and is software-configurable to any address. A multiplexer/Mux is required to communicate to multiple ATECC608A sensors at the default address when on a single bus. If you need to use more than one ATECC608A sensor at the default address， consider using the Qwiic Mux Breakout.。Note：The ATECC608A can be only configured once before it is。PERMANENTLY。locked。. It is advisable that users purchase multiple boards in order to use other configurations and explore the advanced functions of the ATECC608A.。Additionally， this board。IS。capable of encrypting and decrypting data. However， to access these additional features， you will need to contact Microchip and sign an NDA contract to obtain the complete datasheet.。It is recommended that an SparkFun RedBoard Turbo - SAMD21 Development Board is used with this product due to the buffer size required on the I2C bus.。The SparkFun Qwiic Connect System is an ecosystem of I2C sensors， actuators， shields and cables that make prototyping faster and less prone to error. All Qwiic-enabled boards use a common 1mm pitch， 4-pin JST connector. This reduces the amount of required PCB space， and polarized connections mean you can't hook it up wrong.。。Features。Operating Voltage：2.0V-5.5V(。Default on Qwiic System：3.3V。)。Active Current Draw(for ATECC608A)：16 mA。Sleep Current(for ATECC608A)：<150 nA。Guaranteed Unique 72-bit Serial Number。10 Kb EEPROM Memory for Keys， Certificates， and Data。Storage for up to 16 Keys。256-bit Key Length。Internal High-Quality FIPS Random Number Generator(RNG)。Configurable I2C Address(7-bit)：0x60(。Default。)

Description。It's time to say hip hip array for this IR Breakout! The MLX90640 SparkFun IR Array Breakout is equipped with a 32x24 array of thermopile sensors creating， in essence， a low resolution thermal imaging camera. With this breakout you can detect surface temperatures from many feet away with an accuracy of ±1.5℃(best case). To make it even easier to get your infrared image， all communication is enacted exclusively via I2C， utilizing our handy Qwiic system. However， we still have broken out 0.1"-spaced pins in case you prefer to use a breadboard.。This specific IR Array Breakout features a。55°x35°。field of view with a temperature measurement range of -40℃-300℃. The MLX90640 IR Array has pull up resistors attached to the I2C bus； both can be removed by cutting the traces on the corresponding jumpers on the back of the board. Please be aware that the MLX90640 requires complex calculations by the host platform so a regular Arduino Uno(or equivalent)doesn't have enough RAM or flash to complete the complex computations required to turn the raw pixel data into temperature data. You will need a microcontroller with 20，000 bytes or more of RAM. To achieve this， we recommend a Teensy 3.1 or above.。The SparkFun Qwiic connect system is an ecosystem of I2C sensors， actuators， shields and cables that make prototyping faster and less prone to error. All Qwiic-enabled boards use a common 1mm pitch， 4-pin JST connector. This reduces the amount of required PCB space， and polarized connections mean you can't hook it up wrong.。Get Started with the SparkFun IR Array Breakout Guide。Features。Operating Voltage：3V-3.6V。Current Consumption：～18mA。Field of View：55°x35°。Measurement Range：-40℃-300℃。Resolution：±1.5℃。Refresh Rate：0.5Hz-64Hz。I2C Address：0x33。2x Qwiic Connection Ports

Description。LIDAR has never looked so good! This is the LIDAR-Lite v3HP， a compact， high-performance optical distance measurement sensor from Garmin(TM). The LIDAR-Lite v3HP is。the。ideal optical ranging solution for drone， robot， or unmanned vehicle applications. Each sensor is housed in a durable， IPX7-rated housing and includes all the core features and user configurability of the popular LIDAR-Lite v3.。The v3HP is very similar in function to that of the v3 but it can now sample faster at rates greater than 1kHz(where as the v3 is only capable of up to 500Hz). Another improvement is that this v3HP model is more power efficient with current consumption rates 40mA less than the v3(that's 65mA as opposed to 105mA while idle， and 85mA instead of 130mA while acquiring).。Each LIDAR-Lite v3HP has a range of 1m to 40m and features an edge-emitting， 905nm(1.3 watts)， single-stripe laser transmitter， 8m Radian beam divergence， and an optical aperture of 12.5mm. This version of the LIDAR-Lite still operates at 5VDC(6V max)with a peak power of 1.3W and still possesses an accuracy of +/- 2.5cm at >2m. On top of everything else， the LIDAR-Lite is user-configurable， allowing adjustment between accuracy， operating range and measurement time and can be interfaced via I2C or PWM with the attached 200mm cable.。Note：CLASS 1 LASER PRODUCT CLASSIFIED EN/IEC 60825-1 2014. This product is in conformity with performance standards for laser products under 21 CFR 1040， except with respect to those characteristics authorized by Variance Number FDA-2016-V-2943 effective September 27， 2016.。Get Started with the LIDAR-Lite v3HP Guide。Features。Resolution：1 cm。Typical accuracy：+/- 2.5cm at distances greater than 2 meters(Refer to operating manual for complete operating specifications)。Range：1m to 40m。Update rate：Greater than 1kHz。Interface：I2C or PWM。Power(operating voltage)：4.75-5VDC； 6V Max。Current consumption：65ma idle； 85ma during acquisition。Operating temperature：-20℃ to 60℃。Laser wave length/Peak power：905nm/1.3W。Beam divergence：8m Radian。Optical aperture：12.5mm。Water rating：IPX7。Unit dimensions：24.5mm×53.5mm×33.5mm(1.0in×2.1in×1.3in)。Weight：34g(1.2oz)

Description。It's time to say hip hip array for this IR Breakout! The MLX90640 SparkFun IR Array Breakout is equipped with a 32x24 array of thermopile sensors creating， in essence， a low resolution thermal imaging camera. With this breakout you can detect surface temperatures from many feet away with an accuracy of ±1.5℃(best case). To make it even easier to get your low-resolution infrared image， all communication is enacted exclusively via I2C， utilizing our handy Qwiic system. However， we still have broken out 0.1"-spaced pins in case you prefer to use a breadboard.。This specific IR Array Breakout features a 110°x75° field of view with a temperature measurement range of -40℃-300℃. The MLX90640 IR Array has pull up resistors attached to the I2C bus； both can be removed by cutting the traces on the corresponding jumpers on the back of the board. Please be aware that the MLX90640 requires complex calculations by the host platform so a regular Arduino Uno(or equivalent)doesn't have enough RAM or flash to complete the complex computations required to turn the raw pixel data into temperature data. You will need a microcontroller with 20，000 bytes or more of RAM. To achieve this， we recommend a Teensy 3.1 or above.。Note：The I2C address of the MLX90640 is 0x33 and is hardware defined. A multiplexer/Mux is required to communicate to multiple MLX90640 sensors on a single bus. If you need to use more than one MLX90640 sensor consider using the Qwiic Mux Breakout.。The SparkFun Qwiic connect system is an ecosystem of I2C sensors， actuators， shields and cables that make prototyping faster and less prone to error. All Qwiic-enabled boards use a common 1mm pitch， 4-pin JST connector. This reduces the amount of required PCB space， and polarized connections mean you can't hook it up wrong.。Get Started with the SparkFun IR Array Breakout Guide。Features。Operating Voltage：3V-3.6V。Current Consumption：～18mA。Field of View：110°x75°。Measurement Range：-40℃-300℃。Resolution：±1.5℃。Refresh Rate：0.5Hz-64Hz。I2C Address：0x33。2x Qwiic Connection Ports